tattle flag

murny · **Joined:** Fri Oct 14, 2011 12:59 pm **Posts:** 18

Hey guys,

Has any of you used tattle flags on your inlines. Worth the investment ?

DanElliot · **Joined:** Mon Apr 08, 2002 8:59 am **Posts:** 4332

You dont really need to invest much to do it yourself. coat hanger, bead, eye screw and spring (variety pack from canadian tire) and you already have the flag. I did it to my boards and luv watching that flag drop

murny · **Joined:** Fri Oct 14, 2011 12:59 pm **Posts:** 18

thanks for the fast reply. i am all thumbs with tools. can you give some simple directions or post some pics.
if not i'll figure it out.

TheLandshark · **Posted:** Fri Sep 28, 2012 9:43 am

They can be nice for small walleye trolling and or fishing weedy areas. If you are thinking of getting them for the fall walleye, they arent needed.

murny · **Joined:** Fri Oct 14, 2011 12:59 pm **Posts:** 18

thanks for the reply. hoping to sink the flag and the board this november!!!!

TheDL · **Joined:** Thu Jan 27, 2011 11:13 am **Posts:** 435

it's not that hard to make your own tattle flags, and IMO the offshore company is hosing it's customers by charging so much for the flag kit, braid clip, etc...I'm no whiz with tools either, but my diy tattle flag works great. Here's the guide I followed:
http://perchjerker0.tripod.com/home%20made%20tattle%20flags.htm
You just need to buy some stainless steel wire (I'd say coat hanger might be too thick/difficult to work with), a screw, washer, and a variety of springs. It is much easier than you think and dirt cheap to diy.

You might have to experiment with springs, so buy a couple - some tight, some looser, you'll figure it out quick.

DanElliot · **Joined:** Mon Apr 08, 2002 8:59 am **Posts:** 4332

Here are a couple of pics

mallard 58 · **Joined:** Tue Oct 18, 2011 4:53 pm **Posts:** 10

The spring steel wire used on a perch spreaders works well it is thin and very lite and moves very well when a small weed is picked up.

Mallard

Superdad · **Posted:** Mon Oct 01, 2012 2:29 pm

Don't worry about springs - use elastic bands.

Here's what we've done with ours

EASY PEASY!!!!!!!!!!!!!!!!!

http://www.ohiogamefishing.com/community/showthread.php?t=142726&highlight=home+made+tattle

David aka Superdad

J P · **Joined:** Tue Nov 09, 2004 1:32 pm **Posts:** 8

I found these to be the best and very reasonable-

http://www.bottombouncers.com/inline-bo ... g-sprg.htm

Consigliere · **Joined:** Tue Mar 13, 2012 12:32 am **Posts:** 62

Why not just set reel drags so that there is just enough drag to hold the board in place? As soon as a weed, fish, zebra gets onto the bait it will start pulling drag. Reels with a clicker make this dead simple, just listen for the clicker. Good thing is this works at night too.

Walleye 9 · **Joined:** Mon Jan 24, 2011 12:05 pm **Posts:** 1985

Consigliere wrote:

Why not just set reel drags so that there is just enough drag to hold the board in place? As soon as a weed, fish, zebra gets onto the bait it will start pulling drag. Reels with a clicker make this dead simple, just listen for the clicker. Good thing is this works at night too.

That's exactly what I do, as I only run 1 board off each side, and it's hard to tell if it moves. Was worried about a light hookset though. Hooked into 3 fish just under 10 pounds last week, and not one of them moved the board, or pulled it down. As far as I could see anyways. None of them got off, so maybe it's alright.

HOME	Bait&Tackle	Bed&Breakfast	Boat Rentals	Campgrounds	Contact Us
Cottage Rentals	Guides/Fishing Charters	Hotels/Motels	Hunting Supplies	Ice Huts/Ice Guides	Marinas
Outfitters	QUINTE FISHING SERIES	Resorts	Tourism	Trailer Parks	Launches

Quinte Fishing

tattle flag

Who is online